OEM PART NUMBERS — BOSCH:
• Bosch: 9-222-067-016 / 9222067016
• Bosch: 9-222-067-017 / 9222067017
• Bosch: 9-222-067-021 / 9222067021
• Bosch: 9-222-067-024 / 9222067024
INDUSTRY CROSS-REFERENCES:
• Industry: BM322
• Industry: IG-B006H
• Industry: ICM1322
• Other Names: Ignition Control Module
• Other Names: Ignition Module
• Other Names: Switch Unit (Ignition System)
• Other Names: Bosch Electronic Ignition
• Other Names: Magnetic Pickup Module
• Other Names: Reluctor Pickup Module
• Other Names: Holden Ignition Module
• Other Names: Commodore Ignition Module
• Other Names: European Model Ignition Module
• Other Names: Australian Model Ignition Module
PRODUCT SPECIFICATIONS:
• Product Type: Ignition Control Module
• Unit Type: Bosch System
• Ignition System: Magnetic Pick-Up
• Signal Type: Magnetic Reluctor
• Dwell Control: Controlled by Module
• Protection: Transient Protection on All Pins
• Function: Ignition Coil Primary Switching
• Era: 1978-1993 Holden Commodore Era
• Condition: New Aftermarket Replacement
• Quantity: Sold Individually (1 Piece)
• Product Fit: Direct Fit OEM Replacement
• Installation: Direct Bolt-In
• Recommended Use: OE Replacement
• Compliance: CE / ECE Standards
VEHICLE COMPATIBILITY:
• 1978-1993 Holden Commodore (All Generations)
• VB / VC / VH / VK / VL / VN / VP Models
• European Market Variants
• Australian Market Variants
• Select European and USA Vehicles with Bosch System
ENGINE COMPATIBILITY:
• Holden 173 Red L6 2.85L
• Holden 202 Red / Blue / Black L6 3.3L
• Holden 253 V8 4.2L
• Holden 308 V8 5.0L
• Nissan RB30 L6 3.0L (VL Commodore)
• All Bosch Magnetic Pickup Equipped Engines
KEY FEATURES:
• Magnetic Pick-Up System (Reluctor)
• Dwell Controlled by Module
• Transient Protection on All Pins
• Covers European AND Australian Model Variants
• Direct OEM Replacement
• Improved Thermal Design
• Precious Metal Electrical Contacts
• Electronic Snap-Acting Switching
CRITICAL FITMENT NOTES:
• For Bosch Magnetic Pickup Systems ONLY
• Does NOT Fit Hall Effect Pickup Systems
• Does NOT Fit Motronic DME/ECU Systems
• Does NOT Fit Optical Pickup Systems
• Does NOT Fit Coil-on-Plug Systems
• Verify Bosch Part Number Before Ordering
• Confirm European vs Australian Variant
WHAT IS NOT INCLUDED:
• Mounting Hardware / Screws
• Heat Sink / Thermal Paste
• Wiring Harness / Connectors
• Ignition Coil
• Distributor / Distributor Cap / Rotor
• Spark Plug Wires
• Installation Instructions
SYMPTOMS OF FAILURE:
• Engine Will Not Start / No Spark
• Engine Cranks But Does Not Fire
• Engine Stalls After Warming Up
• Intermittent Stalling (Heat Soak)
• Engine Misfire / Rough Running
• Hard Starting When Hot
• Engine Cuts Out Under Load
• Common Failure on Aging Commodore Vehicles
APPLICATION SUMMARY:
• 1978-1993 Holden Commodore (All VB/VC/VH/VK/VL/VN/VP)
• European Model Variant (Bosch 016/017)
• Australian Model Variant (Bosch 021/024)
• Select European and USA Vehicles with Bosch System
PRODUCT NOTICE:
As a parts distributor we mostly sell aftermarket parts (any OEM parts would be noted as such). Aftermarket parts are not sourced from the original vehicle or equipment manufacturer, but are designed to function the same as - if not better than - the original. All parts sold are new.
WARNING - This product may expose you to chemicals such as Carbon Black, Silica, Crystalline which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
Total Reviews (0)
Write the First Review!